Відео

I need to how to re grit these, I’ve tried a couple of things, and it does t work, grit come Off when touching it with a blade

Good video, step-by-step instructions with good camera angles to see how you sharpen. Thanks

What is that? I know it's not railroad track.

This works, thanks!

Good job. Those property lines are really close. I was wondering what the two sunken areas that had water standing in them on the slab? Thanks from Arkansas USA.

Thank you so much for this video. This is all I needed, I am currently having this problem.

Problem with etching a Chinese vg10 knife which is pretty much stainless steel Damascus

I plan on building one hopefully this year. It's all about trial and error on building stuff on your own. Great job regardless cause it's still doing what you need it to do!

I’m a have to pass on this here lump of steel hoss, ain’t no way, I done seen better rebounds in the WNBA

Thank you! Just fixed a bearing that had been a pain for the last days!

Sorry but your rebound test didn't show much rebound you want at least 80 percent rebound to be a actual anvil

Just used this on a subaru bearing that exploded. Only the race left, Worked great, thanks

my ford ranger is like that now when its cold i need to give gas when i start and i have no idle when cold but when its warm i have can it be the glow plugs.

probably better than my solution which is to get a nice mid-width log, some scrap steel plate (admittedly of unknown steel type) and drill holes in it, then bolt the steel plate down onto the log. all supplies and tooling courtesy of a close friend of mine for free. Still, for not having any tools of my own i think it's a great start even if it is not ideal, and it also fosters creativity to overcome hardship caused by the initial lack of tools. Future upgrades include either building a wood table with wheels, or putting wheels on the log itself. If i build the table i have a chemistry solution that can be painted onto wood planks. It turns them jet black and makes them remarkably fire and acid resistant. Should be tough enough to survive stray brief exposure to hot metal.

This video is AWESOME THANK YOU so much 👏👏👏👏🍻

Likelihood of blowing that hydraulic cylinder seal with debris/slag.

If I was U I would replace all brand new while I was doing it plus thanks 4 ur video very helpful

so what was causing the white smoke when cold starting

This work d amazing for me

If the title of this video is “Razor Sharp Knives in Seconds” how come it’s 13 1/2 minutes long?

Well now I want to etch something❤️🔥

Jesus, do something!

Is the antiseize an absolute necessity, I forgot to get it when I was at the parts store. Will it be ok to run the car for 5 minutes to get it home and then take the plugs out again and put antiseize on later?

If they flew off they're probably a half mile away stuck in a wall in the neighbors house😅😂

Where can I find something like this

can you tell me ,where i can get it ! ! please thank you ! !

Are you guys still producing these? Or just the scorpion grinder?

A good deal of that deflection problem could be resolved by making the ram connected sled long enough to go behind the stationary anvil. An alternative (expensive solution) would be roller bearings.

You can tell by the sound it's not right

Thanks mate, keen as to see more vids on your ute about anything could really help me out with my bravo

Following

Omg. There's minutes of my life I will never get back (but thanks 4 yours) 🙆‍♂️

Mild steel is roughly 40lb @ 1"x12"x12". At the price per lb of steel right now that is anything but a poormans anvil

Pour some petrol down this and crank it.,...oh diesel..,.. different story

Thanks to your video mate! Been asking around lucky i stumbled on your video. Me car had the same issue, changed the glow plugs and bwala! Problem solve.

The "poor mans anvil" *proceeds to strike a couple hundred dollare block of steel.

Hot damn! Lol. Great size face, and pretty nice rebound. 🍻

Always wanted to try this but was foiled by not being able to get the wheels . Tried a wheel I made from mdf but found the gringer was a cheap Aldi one that did not have enough power to pull the skin off a thin custard &would not hold the paste. Where can I get the wheels?

How’s that Aluminum pan doing? 😂

Great video nice and straightforward and thank you so much I just removed a outer that I had nothing to get a punch on and I mean nothing incredible trick of the trade 👍

🇲🇦🇲🇦🇲🇦👍

You know man, its a big old chunk of metal, that'll work.

Thank you so much for the tip👍. I have just successfully removed a stubborn race from my trailer hub. It worked !!! Thank you Thank you Thank you! I didn't even use water cooling at the end, just 4 tabs at 90 degrees apart to give my chisel a grab. The heat did the trick too for sure! cheers!

Excellent guide mate, thanks. Found my faulty plug in a blink. Only difference is 7mm nuts on my '05 cheers👍

I wish these were available in the US.

Nice simple build. Going to be making a similar version that fits into a Chinese mini excavator, bucket in reverse of usual excavator orientation. Thanks & subbed.

Horrible rebound but, lots of weight behind it. You could get a one inch plate of something hard to resurface that with

where did you buy that machine

And fanny is your flippen Aunt. Great vid. Thanks, now to change mine!

Od kog materijala su diskovi na tocilu?